Author Topic: An Oak Attacked My Shed! (Hole In Roof)  (Read 699 times)

0 Members and 1 Guest are viewing this topic.

Offline mrclose

  • Hero Member
  • ****
  • Posts: 2,316
An Oak Attacked My Shed! (Hole In Roof)
« on: April 16, 2019, 05:46:33 PM »

We live in a forest of Oaks and they are constantly launching limbs/missiles at us!  ***hair on fire

As you can see from the pictures ... A giant oak attacked my shed! :#@$%:

Fortunately, it was the shed and not our house!
(We just had both the shed and the house re-roofed.)

(Since it is the shed ... I am going to 'attempt' to fix the damage myself.)
super22

Here is what I am going to do and I would like to ask any roofers (or former roofers) their advice before I start?

1) Remove limb .. (Not rocket science)

2) Cut a thin square (5"x5") of wood and using Titebond Ultimate 111 wood glue, attach it to inside of roof.

3) Outside I plan to use leak stopper Rubber Flex Sealant to waterproof the hole. (It's the spray on kind)

4) Next, I plan to cover the hole (outside) with Gorilla Waterproof Patch and Seal Tape.

The next part is where I need the most help!

I have leftover asphalt shingles from the roofing jobs that were done but I don't know the best way to attach the replacement piece?

I hate thinking that I'll need to nail it because of nail holes?

Can I glue the shingle in place?

Thank You for any help you can provide.
(I bolded the material names that I am using for feedback purposes only)

There is a lot riding on this ... my Better Half has promised me a slice of this gorgeous pie!(last photo) If I somehow manage to not make things worse than they are! :whistle:









THE PRIZE ...



KEYLIME PIE!!!
"When you are dead, you don't know that you are dead.
It is difficult only for the others.

It is the same when you are stupid."

~ Anonymous

Offline Sanguine

  • TBR Moderator
  • *****
  • Posts: 33,452
Re: An Oak Attacked My Shed! (Hole In Roof)
« Reply #1 on: April 16, 2019, 06:11:49 PM »
I have no advice, but it's pretty impressive!
Cui bono?

Walk in Wisdom
See then that you walk circumspectly, not as fools but as wise, redeeming the time, because the days are evil.

But the noble make noble plans, and by noble deeds they stand.

Offline roamer_1

  • Hero Member
  • ****
  • Posts: 16,273
Re: An Oak Attacked My Shed! (Hole In Roof)
« Reply #2 on: April 16, 2019, 07:38:46 PM »
@mrclose
Your 'patch' is improper, and will likely fail.
At least it would here.

Personally, I would lay a steel roof right over the whole mess, and quit worrying about the patch at all.

A steel roof would be more durable to impact, is fire resistant, requires no prep, and is more reparable if in fact damage does happen again (just replace the affected panel).

If you do this buy a few spare sheets, as color matching is a problem over years... But even so, the solution is still easy to repair with any industrial DTM paint (you might have to paint the roof), worst case scenario.

As to repairing what you have:

I would fix the sheathing from below by using a hole saw to create a proper plug, affixed with a slat to put it where it needs to be, and filling around it with an epoxy filler. Remove the slat once the epoxy is dry enough to hold, and repeat the process for the areas that were made inaccessible by the slat. Sand with a palm sander to clean it up as much as possible once the epoxy is fully cured.

Fixing the three-tab roofing is a tricky business that takes a knack.
preferrably on a hot day, when the roofing will be more pliable, you use a flat bar (wonderbar) from underneath the affected tiles and those around it, to pry out the nails, lifting the tile and the nails. any 3-tab thus treated will need to be replaced.

Clear about 3 ft across the patch site, fix the top side of the hole, sand, and paint with an oil primer...
Cut a piece of felt to replace the removed felt in the exposed area, well beyond the hole's edges - say a foot in every direction, making certain the bottom edge of the felt is on top of the lower tabs... But not to the degree that it will show.

Then weave the new 3-tab tiles into place, starting from the bottom and working your way up the patch. The uppermost edge, and the sides where the weaving is occurring is the tough part... the good tiles must be pried up enough to allow them to be out of the way enough to nail on the repair pieces without disturbing the nails or breaking the non-repair tiles... Hence the need for a hot day, so the existing tiles will be as pliable as possible. If the roofing is too brittle to do so (which it will be at about half it's life), patching is not possible.

The existing tiles will look disturbed at first on the finished roof - Give em time, and they will lay back down. you can attempt gluing using a roofing tar/ glue to force the process, but they will lay back down eventually regardless.

On a thing that small, I would rather just remove, and re-roof that side. And if the roofing is off, the damaged plywood can just be replaced. No weird fix in the plywood, no break in the felt, and fresh roofing. All of which is a far more guaranteed process, with a predictable outcome.

Then the felt has no seam, you have no worries about exactly matching the 3tab (which you won't) The difference would only have to be close enough to not look out of place, rather than making a patch which will likely be different than the rest of the field.



Share me

Digg  Facebook  SlashDot  Delicious  Technorati  Twitter  Google  Yahoo
Smf